Alex Waithera8 min readUpdated

    Electrolyzer Cost per kW: What a Hydrogen Project Really Pays

    Illustration of an electrolyzer stack with separate rectifier, water treatment, gas and cooling modules.

    Electrolyzer cost per kW depends on what the number includes: the IEA's 2025 installed cost for water electrolysis is $1,920–2,500/kW as a global average and $550–1,100/kW in China, while DOE's equipment-only figures are about half or less of the installed cost. Check the scope of any number before you put it in a model.

    In short: a realistic installed budget outside China is roughly $2,000–2,500/kW, or $200–250 million for 100 MW, before any power generation. Equipment-only prices of $500–1,000/kW are real, but they exclude construction, engineering and installation, and those items often make up more than half of the total.

    This is general pre-feasibility guidance, not procurement or investment advice. Confirm all figures with vendor quotations and qualified engineers.

    The project question: which electrolyzer cost per kW goes in the model?

    A developer usually meets three different numbers that all get called "the electrolyzer price":

    Using a stack or system price where an installed cost belongs can understate a project's capital cost by a factor of two or more. That error then flows straight into the levelized cost of hydrogen, the figure a buyer or lender actually tests.

    What the documented numbers say

    Source and year Scope Figure ($/kW)
    IEA Global Hydrogen Review 2026 annex, 2025 Installed, global average 1,920–2,500
    Same annex, 2025 Installed, China 550–1,100
    Same annex, 2030 stated policies Installed, global average 1,440–1,870
    IEA Global Hydrogen Review 2025, 2024 Made and installed outside China 2,000–2,600
    DOE PEM targets, 2022 status PEM system, uninstalled 1,000
    DOE alkaline targets, 2022 status Alkaline system, uninstalled 500
    DOE Program Record 24005, 2022 dollars PEM, installed baseline about 2,000

    Four details matter when you read that table.

    The IEA's figure is an installed cost. Its CAPEX includes the electrolyzer system, electrical equipment, gas treatment, balance of plant and EPC, but not the power generation assets. It does not split the figure by technology, and the IEA does not list other regions separately.

    DOE's system cost excludes installation. Its footnotes say engineering, procurement, construction and permitting are not included. DOE's Program Record 24005 assumes installation and indirect costs roughly equal to the uninstalled system cost, so its installed cost is about twice the uninstalled cost.

    More than half is often not the machine. The IEA's 2025 review reported that engineering, procurement, construction and contingency make up more than half of the $2,000–2,600/kW cost outside China.

    A cheap import does not automatically give a cheap project. The same IEA review put Chinese electrolyzers installed outside China at $1,500–2,400/kW once transport and tariffs were included, and said this is not significantly lower than installing other producers' equipment when all factors are considered.

    The European Hydrogen Observatory offers a useful way to set out scope. For a European project of 100 MW in an advanced stage, it splits CAPEX into stack, balance of plant, other utilities and other CAPEX. Its "other CAPEX" category includes land and grid fees, insurance, permitting, feasibility work, contingency and EPC management, which is a good checklist for what a headline price leaves out.

    Worked example: normalizing two 100 MW offers

    Suppose you hold two hypothetical offers for a 100 MW plant outside China. All values are illustrative assumptions, not quotes, project data or H2Hub outputs. Offer A looks $300/kW cheaper on the headline, but it leaves more scope to the buyer.

    Item ($/kW) Offer A Offer B
    Quoted price (headline) 650 950
    Rectifier and transformer +120 (excluded) included
    Gas purification +40 (excluded) included
    Water treatment and cooling +90 +60
    Installation, EPC and contingency +900 +800
    Owner's costs: land, grid, permits +250 +250
    Installed cost $2,050/kW $2,060/kW
    Project cost for 100 MW $205 million $206 million

    Once normalized, the $300/kW headline advantage has shrunk to almost nothing. Both totals fall inside the IEA's installed range, and EPC, contingency and owner's costs are 56% and 51% of the two totals.

    What each $/kW means per kilogram of hydrogen

    To translate installed cost into hydrogen cost, this example uses these illustrative assumptions: 55 kWh/kg system electricity use (DOE's 2022 status), an 8% discount rate over 20 years (capital recovery factor 0.10185), and fixed operating cost of 3% of capital cost per year, the IEA annex assumption.

    Installed cost 3,000 full-load hours 5,000 full-load hours 8,000 full-load hours
    $1,000/kW $2.42/kg $1.45/kg $0.91/kg
    $1,500/kW $3.63/kg $2.18/kg $1.36/kg
    $2,000/kW $4.83/kg $2.90/kg $1.81/kg
    $2,500/kW $6.04/kg $3.63/kg $2.27/kg

    These figures are capital recovery plus fixed operating cost only. They exclude electricity, stack replacement, water, compression and taxes. At $40/MWh, for example, electricity would add $2.20/kg at 55 kWh/kg.

    The useful rule of thumb: every $100/kW of installed cost is worth about $0.24/kg at 3,000 full-load hours, $0.15/kg at 5,000, and $0.09/kg at 8,000. A project running 8,000 hours can tolerate a higher price much more easily than one running 3,000 hours. Our guide to electrolyzer utilization and the cost of hydrogen works through that trade-off in detail.

    DOE's own results point the same way. In Program Record 24005, moving from $1,500/kW to $2,500/kW raises its hybrid wind-solar scenario (74% capacity factor) from $4.40/kg to $6.00/kg, in 2022 dollars and before tax credits.

    Watch the ReneEnergy video: What Does an Electrolyzer Cost per Kilowatt Today.

    What the example leaves out

    Real installed costs depend on site, scale and scope, and no public benchmark replaces a quote. PEM usually costs more than alkaline on equipment price, but whether that gap matters depends on stack life and your power profile, which our PEM vs alkaline comparison tests directly. Compression, hydrogen storage and the power generation assets also sit outside these figures. On a real project they can change the budget substantially.

    Five questions to ask before you use a $/kW figure

    1. What is the boundary? Stack, system or installed. Get it in writing.
    2. Who supplies the rectifier, transformer and water treatment? These are common exclusions.
    3. Does the price include EPC, contingency and owner's costs? If not, add them yourself.
    4. Which year and currency? The IEA and DOE figures above use different years and bases.
    5. Which hours does the project run? A $/kW difference only becomes a $/kg difference once you know this.

    Try it in H2Hub

    You can start a project in H2Hub for free, without an account or a card, for the site you are screening. Keep this example's inputs beside you as the baseline: 100 MW, $2,050/kW installed, 55 kWh/kg and your expected full-load hours, then see which assumption moves your result most.

    Your first full project and its PDF report are free; downloading the PDF needs a free sign-in. Re-running with new inputs, such as a second offer's installed cost, or starting a second project requires a subscription, so it is worth choosing your strongest case first. The LCOH Lab is a subscriber tool for working through cost inputs in more depth; signed-out visitors see an introduction.

    A note on pre-feasibility

    The numbers above are a calculation from stated assumptions. They are not forecasts, market prices or H2Hub-generated results, and they are not a substitute for vendor quotes or engineering estimates.

    Frequently asked questions

    How much does an electrolyzer cost per MW?

    At the IEA's 2025 installed global average of $1,920–2,500/kW, a megawatt costs about $1.9–2.5 million installed, excluding power generation. Equipment-only prices are lower, so check the scope of any figure you are given.

    How much cheaper are Chinese electrolyzers?

    The IEA reports a 2025 installed cost of $550–1,100/kW in China. Outside China, transport, tariffs and local construction narrow the gap considerably, and the IEA's 2025 review found Chinese equipment installed abroad cost $1,500–2,400/kW.

    Is alkaline cheaper than PEM per kW?

    On DOE's 2022 status, uninstalled system cost is $500/kW for alkaline and $1,000/kW for PEM. Installed project costs are affected by scope, location and supplier, so compare offers on the same basis.

    Will electrolyzer costs fall?

    The IEA's stated-policies assumptions fall to $1,440–1,870/kW for the global average by 2030. These are scenario assumptions, not guaranteed prices, and actual costs will depend on project scope and supply chains.

    Primary sources and further reading

    1. International Energy Agency — Global Hydrogen Review 2026: Assumptions Annex. Installed cost ranges, scope and fixed operating cost.
    2. International Energy Agency — Global Hydrogen Review 2025: Executive summary. 2024 installed cost outside China, EPC share and Chinese equipment installed abroad.
    3. U.S. Department of Energy — Technical Targets for Proton Exchange Membrane Electrolysis, page updated 29 May 2026.
    4. U.S. Department of Energy — Technical Targets for Liquid Alkaline Electrolysis, page updated 29 May 2026.
    5. U.S. Department of Energy — Hydrogen Program Record 24005, 20 May 2024. Installed cost assumptions and scenario results.
    6. European Hydrogen Observatory — Electrolyser cost. CAPEX categories for a European 100 MW project, reference year 2025.

    Editorial verification: 8 November 2026. Worked examples are calculations from stated assumptions, not forecasts, market prices or H2Hub-generated results.

    Sources

    Explore project tools

    Related articles

    Test your own project assumptions

    H2Hub models power, water and hydrogen costs together — every figure shows its source, date and confidence.

    Test your installed cost in H2Hub — start free

    H2Hub produces preliminary project-development analysis. It is not a substitute for licensed engineering, FEED, due diligence or investment advice.